SC598 linux waiting for /dev/mmcblk0p1...

can anyone help? I have tried multiple times rebuilding the full version, re flashing the u-boot both with the original version without the sd card line both compiled and not compiled. when compiled, no matter what it gets stuck with this load out

=> setenv mmcargs 'setenv bootargs root=/dev/mmcblk0p1 rw rootfstype=ext4 rootw'
=> setenv mmcboot 'mmc rescan; run mmcload; run mmcargs; bootm ${loadaddr};'
=> setenv mmcload 'ext4load mmc 0:1 ${loadaddr} /boot/${imagefile};'
=> run mmcboot
8803182 bytes read in 382 ms (22 MiB/s)
## Loading kernel from FIT Image at 90000000 ...
Using 'conf-1' configuration
Verifying Hash Integrity ... OK
Trying 'kernel-1' kernel subimage
Description: Linux kernel
Type: Kernel Image
Compression: gzip compressed
Data Start: 0x900000e0
Data Size: 6031809 Bytes = 5.8 MiB
Architecture: AArch64
OS: Linux
Load Address: 0x9a200000
Entry Point: 0x9a200000
Hash algo: sha1
Hash value: f8258319cd2c8e613d173a7112aa0c25add52024
Sign algo: sha1,rsa2048:
Sign value: unavailable
Verifying Hash Integrity ... sha1+ sha1,rsa2048:- OK
## Loading ramdisk from FIT Image at 90000000 ...
Using 'conf-1' configuration
Verifying Hash Integrity ... OK
Trying 'ramdisk-3' ramdisk subimage
Description: Initial Ram File System
Type: RAMDisk Image
Compression: uncompressed
Data Start: 0x905c7d6c
Data Size: 2740249 Bytes = 2.6 MiB
Architecture: AArch64
OS: Linux
Load Address: 0x9c000000
Entry Point: 0x9c000000
Hash algo: sha1
Hash value: f117da5772cd101d5323764dabef212e36ef102a
Sign algo: sha1,rsa2048:
Sign value: unavailable
Verifying Hash Integrity ... sha1+ sha1,rsa2048:- OK
Loading ramdisk from 0x905c7d6c to 0x9c000000
## Loading fdt from FIT Image at 90000000 ...
Using 'conf-1' configuration
Verifying Hash Integrity ... OK
Trying 'fdt-2' fdt subimage
Description: Flattened Device Tree Blob
Type: Flat Device Tree
Compression: uncompressed
Data Start: 0x905c0bdc
Data Size: 28795 Bytes = 28.1 KiB
Architecture: AArch64
Load Address: 0x99000000
Hash algo: sha1
Hash value: 4ef4c20f954f82bdd57d1e725baeaf73e181da23
Sign algo: sha1,rsa2048:
Sign value: unavailable
Verifying Hash Integrity ... sha1+ sha1,rsa2048:- OK
Loading fdt from 0x905c0bdc to 0x99000000
Booting using the fdt blob at 0x99000000
Working FDT set to 99000000
Uncompressing Kernel Image
Using Device Tree in place at 0000000099000000, end 000000009900a07a
Working FDT set to 99000000

Starting kernel ...

[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x412fd050]
[ 0.000000] Linux version 5.15.168-yocto-standard (oe-user@oe-host) (aarch644
[ 0.000000] Machine model: ADI 64-bit SC598 SOM EZ Kit
[ 0.000000] earlycon: adi_uart0 at MMIO 0x0000000031003000 (options '')
[ 0.000000] printk: bootconsole [adi_uart0] enabled
[ 0.000000] efi: UEFI not found.
[ 0.000000] Reserved memory: SRAM at 0x0000000020040000, size 256 KiB
[ 0.000000] OF: reserved mem: initialized node sram1-reserved@20040000, comps
[ 0.000000] Reserved memory: created DMA memory pool at 0x0000000020084000, B
[ 0.000000] OF: reserved mem: initialized node vdev0buffer@20084000, compatil
[ 0.000000] Reserved memory: created DMA memory pool at 0x00000000200a8000, B
[ 0.000000] OF: reserved mem: initialized node vdev0buffer@200A8000, compatil
[ 0.000000] NUMA: No NUMA configuration found
[ 0.000000] NUMA: Faking a node at [mem 0x0000000020040000-0x000000009ffffff]
[ 0.000000] NUMA: NODE_DATA [mem 0x9ff4cf00-0x9ff4efff]
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000020040000-0x000000009fffffff]
[ 0.000000] DMA32 empty
[ 0.000000] Normal empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000020040000-0x000000002007ffff]
[ 0.000000] node 0: [mem 0x0000000090000000-0x000000009fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000020040000-0x000000009fffffff]
[ 0.000000] On node 0, zone DMA: 64 pages in unavailable ranges
[ 0.000000] On node 0, zone DMA: 32640 pages in unavailable ranges
[ 0.000000] percpu: Embedded 27 pages/cpu s69720 r8192 d32680 u110592
[ 0.000000] Detected VIPT I-cache on CPU0
[ 0.000000] CPU features: detected: GIC system register CPU interface
[ 0.000000] CPU features: detected: Virtualization Host Extensions
[ 0.000000] CPU features: detected: Qualcomm erratum 1009, or ARM erratum 129
[ 0.000000] CPU features: detected: ARM errata 1165522, 1319367, or 1530923
[ 0.000000] alternatives: patching kernel code
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 64575
[ 0.000000] Policy zone: DMA
[ 0.000000] Kernel command line: root=/dev/mmcblk0p1 rw rootfstype=ext4 rooti
[ 0.000000] Dentry cache hash table entries: 32768 (order: 6, 262144 bytes, )
[ 0.000000] Inode-cache hash table entries: 16384 (order: 5, 131072 bytes, l)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 236772K/262400K available (8448K kernel code, 1258K rwda)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] trace event string verifier disabled
[ 0.000000] rcu: Preemptible hierarchical RCU implementation.
[ 0.000000] rcu: RCU event tracing is enabled.
[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=1.
[ 0.000000] Trampoline variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 ji.
[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1
[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode
[ 0.000000] GICv3: 384 SPIs implemented
[ 0.000000] GICv3: 0 Extended SPIs implemented
[ 0.000000] GICv3: Distributor has no Range Selector support
[ 0.000000] Root IRQ handler: gic_handle_irq
[ 0.000000] GICv3: 16 PPIs implemented
[ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x0000000031240000
[ 0.000000] arch_timer: cp15 timer(s) running at 31.25MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycless
[ 0.000000] sched_clock: 56 bits at 31MHz, resolution 32ns, wraps every 4398s
[ 0.008071] clocksource: cs_adi_gptimer: mask: 0xffffffff max_cycles: 0xffffs
[ 0.017929] sched_clock: 32 bits at 125MHz, resolution 8ns, wraps every 1717s
[ 0.026290] Console: colour dummy device 80x25
[ 0.030661] Calibrating delay loop (skipped), value calculated using timer f)
[ 0.040944] pid_max: default: 4096 minimum: 301
[ 0.045534] LSM: Security Framework initializing
[ 0.050186] Mount-cache hash table entries: 512 (order: 0, 4096 bytes, linea)
[ 0.057309] Mountpoint-cache hash table entries: 512 (order: 0, 4096 bytes, )
[ 0.067085] rcu: Hierarchical SRCU implementation.
[ 0.072521] EFI services will not be available.
[ 0.077151] smp: Bringing up secondary CPUs ...
[ 0.081541] smp: Brought up 1 node, 1 CPU
[ 0.085517] SMP: Total of 1 processors activated.
[ 0.090230] CPU features: detected: 32-bit EL0 Support
[ 0.095362] CPU features: detected: Data cache clean to the PoU not requirede
[ 0.103977] CPU features: detected: CRC32 instructions
[ 0.109112] CPU features: detected: RCpc load-acquire (LDAPR)
[ 0.114856] CPU features: detected: LSE atomic instructions
[ 0.120429] CPU features: detected: Speculative Store Bypassing Safe (SSBS)
[ 0.128583] CPU: All CPU(s) started at EL2
[ 0.133570] devtmpfs: initialized
[ 0.143421] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, ms
[ 0.153113] futex hash table entries: 16 (order: -2, 1024 bytes, linear)
[ 0.159989] pinctrl core: initialized pinctrl subsystem
[ 0.165376] DMI not present or invalid.
[ 0.169722] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.176207] DMA: preallocated 128 KiB GFP_KERNEL pool for atomic allocations
[ 0.183168] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA pool for atomic alls
[ 0.190884] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA32 pool for atomic as
[ 0.198862] audit: initializing netlink subsys (disabled)
[ 0.204916] thermal_sys: Registered thermal governor 'step_wise'
[ 0.205295] audit: type=2000 audit(0.116:1): state=initialized audit_enabled1
[ 0.218958] cpuidle: using governor menu
[ 0.223135] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[ 0.229814] ASID allocator initialised with 65536 entries
[ 0.235443] Serial: AMBA PL011 UART driver
[ 0.261125] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages
[ 0.267913] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages
[ 0.274486] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[ 0.281164] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages
[ 0.289898] cryptd: max_cpu_qlen set to 1000
[ 0.296761] ACPI: Interpreter disabled.
[ 0.300682] iommu: Default domain type: Translated
[ 0.305648] iommu: DMA domain TLB invalidation policy: strict mode
[ 0.312040] SCSI subsystem initialized
[ 0.315941] usbcore: registered new interface driver usbfs
[ 0.321310] usbcore: registered new interface driver hub
[ 0.326628] usbcore: registered new device driver usb
[ 0.332459] i2c-adi-twi 31001400.twi: ADI on-chip I2C TWI Controller, regs_b)
[ 0.343124] gpio-496 (eeprom-en): hogged as output/low
[ 0.348966] gpio-497 (pushbutton-en): hogged as output/low
[ 0.355111] gpio-498 (~microsd-spi): hogged as output/high
[ 0.360852] gpio-499 (~ftdi-usb-en): hogged as output/low
[ 0.366914] gpio-500 (~can-en): hogged as output/high
[ 0.372221] gpio-502 (adau1962-en): hogged as output/low
[ 0.377788] gpio-503 (adau1979-en): hogged as output/low
[ 0.383764] gpio-504 (octal-spi-cs-en): hogged as output/low
[ 0.390089] gpio-505 (~spdif-digital-en): hogged as output/high
[ 0.396674] gpio-506 (~spdif-optical-en): hogged as output/high
[ 0.403258] gpio-507 (audio-jack-sel): hogged as output/high
[ 0.409582] gpio-508 (~mlb-en): hogged as output/high
[ 0.414899] gpio-509 (~eth1-en): hogged as output/low
[ 0.420207] gpio-510 (~eth1-reset): hogged as output/low
[ 0.426183] gpio-511 (~gige-reset): hogged as output/high
[ 0.432032] i2c-adi-twi 31001600.twi: ADI on-chip I2C TWI Controller, regs_b)
[ 0.440898] pps_core: LinuxPPS API ver. 1 registered
[ 0.445717] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giom>
[ 0.454871] PTP clock support registered
[ 0.459642] Advanced Linux Sound Architecture Driver Initialized.
[ 0.466700] clocksource: Switched to clocksource arch_sys_counter
[ 0.508675] VFS: Disk quotas dquot_6.6.0
[ 0.518796] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.534997] pnp: PnP ACPI: disabled
[ 0.555725] NET: Registered PF_INET protocol family
[ 0.560656] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linea)
[ 0.575526] tcp_listen_portaddr_hash hash table entries: 256 (order: 0, 4096)
[ 0.594717] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes,)
[ 0.610740] TCP established hash table entries: 2048 (order: 2, 16384 bytes,)
[ 0.622710] TCP bind hash table entries: 2048 (order: 3, 32768 bytes, linear)
[ 0.638724] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.650830] UDP hash table entries: 128 (order: 0, 4096 bytes, linear)
[ 0.662704] UDP-Lite hash table entries: 128 (order: 0, 4096 bytes, linear)
[ 0.678891] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.694954] RPC: Registered named UNIX socket transport module.
[ 0.700792] RPC: Registered udp transport module.
[ 0.710696] RPC: Registered tcp transport module.
[ 0.718696] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.735313] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters ae
[ 0.743209] Unpacking initramfs...
[ 1.016658] Freeing initrd memory: 2676K
[ 1.450250] Initialise system trusted keyrings
[ 1.454920] workingset: timestamp_bits=42 max_order=16 bucket_order=0
[ 1.469643] NFS: Registering the id_resolver key type
[ 1.474668] Key type id_resolver registered
[ 1.478732] Key type id_legacy registered
[ 1.482846] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 1.489440] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registerin.
[ 1.496864] jffs2: version 2.2. (NAND) �© 2001-2006 Red Hat, Inc.
[ 1.539565] Key type asymmetric registered
[ 1.543561] Asymmetric key parser 'x509' registered
[ 1.548530] Block layer SCSI generic (bsg) driver version 0.4 loaded (major )
[ 1.555841] io scheduler mq-deadline registered
[ 1.560336] io scheduler kyber registered
[ 1.571928] gpio-478 (~uart0-en): hogged as output/low
[ 1.577585] gpio-479 (~uart0-flow-en): hogged as output/high
[ 1.583725] gpio-480 (~spi2d2-d3-en): hogged as output/low
[ 1.589690] gpio-481 (~spi2flash-cs): hogged as output/low
[ 1.595654] gpio-486 (emmc-en): hogged as output/low
[ 1.601096] gpio-487 (emmc-som-en): hogged as output/high
[ 1.606972] gpio-493 (led1-en): hogged as output/low
[ 1.612412] gpio-494 (led2-en): hogged as output/low
[ 1.617858] gpio-495 (led3-en): hogged as output/low
[ 1.623338] EINJ: ACPI disabled.
[ 1.627060] adi-dma 31022000.dma: Creating new peripheral DMA controller inse
[ 1.636059] adi-dma 31023000.dma: Creating new peripheral DMA controller inse
[ 1.644871] adi-dma 3102d000.dma: Creating new peripheral DMA controller inse
[ 1.657045] adi-dma 310a7000.dma: Creating new peripheral DMA controller inse
[ 1.665954] adi-dma 31026000.dma: Creating new peripheral DMA controller inse
[ 1.678049] adi-dma 3109a000.dma: Creating new MDMA controller instance
[ 1.687059] adi-trigger-routing-unit 3108a000.tru: Connecting master 134 to 0
[ 1.694787] adi-trigger-routing-unit 3108a000.tru: Connecting master 135 to 4
[ 1.702591] adi-trigger-routing-unit 3108a000.tru: Connecting master 136 to 8
[ 1.713441] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 1.721187] ADI serial driver
[ 1.724279] adi-uart4 31003000.uart: Serial probe
[ 1.728987] 31003000.uart: ttySC0 at MMIO 0x0 (irq = 0, base_baud = 7812500)4
[ 1.737395] printk: console [ttySC0] enabled
[ 1.737395] printk: console [ttySC0] enabled
[ 1.745750] printk: bootconsole [adi_uart0] disabled
[ 1.745750] printk: bootconsole [adi_uart0] disabled
[ 1.757308] cacheinfo: Unable to detect cache hierarchy for CPU 0
[ 1.763453] sram_mmap sram-mmap@0: assigned reserved memory node sram1-reser0
[ 1.773696] spi-nor spi2.0: is25lp01g (131072 Kbytes)
[ 1.782848] 5 fixed-partitions partitions found on MTD device spi2.0
[ 1.789097] Creating 5 MTD partitions on "spi2.0":
[ 1.793856] 0x000000000000-0x000000040000 : "U-Boot SPL"
[ 1.800685] 0x000000040000-0x000000100000 : "U-Boot Proper"
[ 1.807546] 0x000000100000-0x000000120000 : "U-Boot Environment"
[ 1.814751] 0x000000120000-0x000001020000 : "FIT Image"
[ 1.821515] 0x000001020000-0x000008000000 : "JFFS2 Formatted RFS"
[ 1.828894] adi-spi3 31030000.spi: registered ADI SPI controller spi2
[ 1.835946] tun: Universal TUN/TAP device driver, 1.6
[ 1.841548] adi-dwmac 31040000.ethernet: IRQ eth_wake_irq not found
[ 1.847746] adi-dwmac 31040000.ethernet: IRQ eth_lpi not found
[ 1.853624] adi-dwmac 31040000.ethernet: PTP uses main clock
[ 1.859411] adi-dwmac 31040000.ethernet: User ID: 0x10, Synopsys ID: 0x52
[ 1.866071] adi-dwmac 31040000.ethernet: DWMAC4/5
[ 1.870842] adi-dwmac 31040000.ethernet: DMA HW capability register supported
[ 1.877926] adi-dwmac 31040000.ethernet: RX Checksum Offload Engine supported
[ 1.885041] adi-dwmac 31040000.ethernet: TX Checksum insertion supported
[ 1.891724] adi-dwmac 31040000.ethernet: Wake-Up On Lan supported
[ 1.897800] adi-dwmac 31040000.ethernet: TSO supported
[ 1.902921] adi-dwmac 31040000.ethernet: Enable RX Mitigation via HW Watchdor
[ 1.910561] adi-dwmac 31040000.ethernet: Enabled L3L4 Flow TC (entries=8)
[ 1.917331] adi-dwmac 31040000.ethernet: Enabled RFS Flow TC (entries=8)
[ 1.924015] adi-dwmac 31040000.ethernet: TSO feature enabled
[ 1.929656] adi-dwmac 31040000.ethernet: SPH feature enabled
[ 1.935304] adi-dwmac 31040000.ethernet: Using 32 bits DMA width
[ 1.968445] VFIO - User Level meta-driver version: 0.3
[ 1.992106] dwc2 310c5000.usb: DWC OTG Controller
[ 1.996711] dwc2 310c5000.usb: new USB bus registered, assigned bus number 1
[ 2.003776] dwc2 310c5000.usb: irq 44, io mem 0x310c5000
[ 2.009697] hub 1-0:1.0: USB hub found
[ 2.013379] hub 1-0:1.0: 1 port detected
[ 2.018280] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.024870] ehci-platform: EHCI generic platform driver
[ 2.030124] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 2.036177] ohci-platform: OHCI generic platform driver
[ 2.041823] usbcore: registered new interface driver usb-storage
[ 2.048676] i2c_dev: i2c /dev entries driver
[ 2.054263] adi_sc59x_tmu 31016800.thermal: Fault limit: 85 C, Alert limit: C
[ 2.061552] adi_sc59x_tmu 31016800.thermal: Gain 0x4, offset 32064
[ 2.067672] adi_sc59x_tmu 31016800.thermal: SC59x Thermal Monitoring Unit ace
[ 2.075680] adi_wdt: initialized: timeout=20 sec (nowayout=0)
[ 2.082237] sdhci: Secure Digital Host Controller Interface driver
[ 2.088300] sdhci: Copyright(c) Pierre Ossman
[ 2.092594] Synopsys Designware Multimedia Card Interface Driver
[ 2.098723] sdhci-pltfm: SDHCI platform and OF driver helper
[ 2.105341] ledtrig-cpu: registered to indicate activity on CPUs
[ 2.112374] ADI hardware CRC crypto driver
[ 2.116904] adi-hmac-crc 310a5000.crc: initialized
[ 2.122038] adi-pkte 310cd000.pkte: Selected ARM mode
[ 2.127269] adi-pkte 310cd000.pkte: will run requests pump with realtime priy
[ 2.137671] adi_remoteproc 28240000.core1-rproc: Resource table set, enable g
[ 2.145503] adi_remoteproc 28240000.core1-rproc: Load verification enabled
[ 2.152293] mmc0: SDHCI controller on 310c7000.mmc [310c7000.mmc] using ADMA
[ 2.159502] remoteproc remoteproc0: core1-rproc is available
[ 2.165784] adi_remoteproc 28a40000.core2-rproc: Resource table set, enable g
[ 2.173510] remoteproc remoteproc0: powering up core1-rproc
[ 2.179043] remoteproc remoteproc0: Booting fw image adi_adsp_core1_fw.ldr, 8
[ 2.187165] adi_remoteproc 28a40000.core2-rproc: Load verification enabled
[ 2.195920] remoteproc remoteproc1: core2-rproc is available
[ 2.203272] remoteproc remoteproc1: powering up core2-rproc
[ 2.211776] remoteproc remoteproc1: Booting fw image adi_adsp_core2_fw.ldr, 8
[ 2.230810] virtio_rpmsg_bus virtio0: creating channel sharc-echo addr 0x97
[ 2.237758] virtio_rpmsg_bus virtio0: creating channel sharc-echo-cap addr 01
[ 2.245073] virtio_rpmsg_bus virtio0: rpmsg host is online
[ 2.250448] remoteproc0#vdev0buffer: registered virtio0 (type 7)
[ 2.256549] virtio_rpmsg_bus virtio1: creating channel sharc-echo addr 0x98
[ 2.263513] virtio_rpmsg_bus virtio1: creating channel sharc-echo-cap addr 02
[ 2.270895] virtio_rpmsg_bus virtio1: rpmsg host is online
[ 2.276273] remoteproc remoteproc0: remote processor core1-rproc is now up
[ 2.283164] remoteproc1#vdev0buffer: registered virtio1 (type 7)
[ 2.289223] remoteproc remoteproc1: remote processor core2-rproc is now up
[ 2.327301] mmc0: new high speed MMC card at address 0001
[ 2.333436] mmcblk0: mmc0:0001 IS008G 7.28 GiB
[ 2.340996] mmcblk0boot0: mmc0:0001 IS008G 4.00 MiB
[ 2.348062] mmcblk0boot1: mmc0:0001 IS008G 4.00 MiB
[ 2.354819] mmcblk0rpmb: mmc0:0001 IS008G 4.00 MiB, chardev (244:0)
[ 2.608504] NET: Registered PF_PACKET protocol family
[ 2.613531] 8021q: 802.1Q VLAN Support v1.8
[ 2.617624] Key type dns_resolver registered
[ 2.622464] registered taskstats version 1
[ 2.626470] Loading compiled-in X.509 certificates
[ 2.637158] adsp-sru-ctrl 310ca000.sru-ctrl-dai1: Started without extended s)
[ 2.648556] sc5xx-i2s-dai 31002400.i2s: SPORT create success
[ 2.657150] printk: console [netcon0] enabled
[ 2.661408] netconsole: network logging started
[ 2.666086] clk: Disabling unused clocks
[ 2.669950] ALSA device list:
[ 2.672813] #0: sc5xx-asoc-card
[ 2.679310] Freeing unused kernel memory: 2368K
[ 2.684025] Run /init as init process
[ 2.755182]
[ 2.755182] Analog Initial Ram Filesystem
[ 2.755182] www.analog.com
[ 2.755182] www.yoctoproject.org
[ 2.755182]
[ 2.755182] Analog [Initramfs]: Preparing Operating System....
[ 2.755182] Analog [Initramfs]: Mounting Root File System...
[ 2.797502] Waiting for /dev/mmcblk0p1...

what am i doing wrong? I followed the instructions on the webpage

Hi Daniel,

Your kernel log seems to show the following:

[ 2.327301] mmc0: new high speed MMC card at address 0001
[ 2.333436] mmcblk0: mmc0:0001 IS008G 7.28 GiB
[ 2.340996] mmcblk0boot0: mmc0:0001 IS008G 4.00 MiB
[ 2.348062] mmcblk0boot1: mmc0:0001 IS008G 4.00 MiB
[ 2.354819] mmcblk0rpmb: mmc0:0001 IS008G 4.00 MiB, chardev (244:0)

while the kernel is waiting for a partition named mmcblk0p1, as mentioned here:

[ 2.797502] Waiting for /dev/mmcblk0p1...

Which seems to indicate that the boot partition has been incorrectly specified for the kernel to correctly load the partition.

In order to verify this, could you boot via another boot method such as nfs/spiboot and attempt to mount the sdcard partitions in question? If this is indeed the case, could you attempt following these instructions in regards to formatting the SD card and try again: https://github.com/analogdevicesinc/lnxdsp-adi-meta/wiki/Getting-Started-with-ADSP%E2%80%90SC598-(Linux-for-ADSP%E2%80%90SC5xx-Processors-3.1.2)#formatting-the-sd-card . This should generate the correct partition.

If you would like to change the boot partition that you would want to boot into, you can change the following inside u-boot proper:

=> editenv mmcargs
setenv bootargs root=/dev/mmcblk0p1 rw rootfstype=ext4 rootwait earlycon=adi_uart,0x31003000 console=ttySC0,115200 vmalloc=512M

Here, change the argument root=/dev/mmcblk0p1 to the required partition name, i.e, root=/dev/xyz

To add a bit more context, this is what the expected log should look like:

[ 2.290046] mmc0: new high speed MMC card at address 0001
[ 2.296181] mmcblk0: mmc0:0001 IS008G 7.28 GiB
[ 2.303187] mmcblk0: p1
[ 2.306400] mmcblk0boot0: mmc0:0001 IS008G 4.00 MiB
[ 2.313384] mmcblk0boot1: mmc0:0001 IS008G 4.00 MiB
[ 2.320042] mmcblk0rpmb: mmc0:0001 IS008G 4.00 MiB, chardev (244:0)

As you can see, the mmcblk0: p1 is clearly mentioned. Once booted, I can see the following:

root@adsp-sc598-som-ezkit:~# ls /dev/mmcblk0
mmcblk0 mmcblk0boot0 mmcblk0boot1 mmcblk0p1 mmcblk0rpmb

I placed several different SD cards ranging from 4GB to 32GB and lsblk does not even show the disk. I have tried rebooting the board and I get the same results. No SD card seems to be found.

lsblk
NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINTS
mtdblock0 31:0 0 256K 0 disk
mtdblock1 31:1 0 768K 0 disk
mtdblock2 31:2 0 128K 0 disk
mtdblock3 31:3 0 15M 0 disk
mtdblock4 31:4 0 111.9M 0 disk
mmcblk0 179:0 0 7.3G 0 disk
mmcblk0boot0 179:32 0 4M 1 disk
mmcblk0boot1 179:64 0 4M 1 disk

Is it possible the sd card port on the board is bad?

Hi Daniel,

Daniel78 said:
No SD card seems to be found.

Has it been formatted following the steps mentioned in the guide? Based on the above, I do not see the partition.

As shown in my log, I would expect a partition to have been created called p1 and show up as /dev/mmcblk0p1.

Daniel78 said:
Is it possible the sd card port on the board is bad?

I do not think the sdcard port is bad since it is visible in the kernel logs.

Hi Utsav,

I have tried everything I can think of, I've recompiled the code, changed SD cards, followed the instructions on how to format the sd card, but now when I attempt to boot via mmcboot with

ADSP_SC598_SDCARD = "1"
I get

run mmcboot
** No partition table - mmc 0 **
Couldn't find partition mmc 0:1
Can't set block device
Wrong Image Format for bootm command
ERROR: can't get kernel image!

and nfsboot does not show any sd card plugged in, even though one is plugged in

Hi Daniel,

Daniel78 said:
** No partition table - mmc 0 **

Daniel78 said:
and nfsboot does not show any sd card plugged in, even though one is plugged in

Both these indicate that the SD card has probably not been formatted correctly. The u-boot issue seems to indicate that there is no partition table there whatsoever - i.e, probably the device was fully erased and not reformatted.

Could you please share what the partition table looks like after following the SD card formatting steps (from the system where compilation/formatting is taking place)? What are the exact steps that you are doing in order to format/populate the SD card.

I want to ensure that all contents required for a boot are present prior to attempting boot.

Hi Utsav,

I am following the instructions on https://github.com/analogdevicesinc/lnxdsp-adi-meta/wiki/Getting-Started-with-ADSP%E2%80%90SC598-(Linux-for-ADSP%E2%80%90SC5xx-Processors-3.1.2)#formatting-the-sd-card

gparted shows an ext4 and everything appears to be there, but I'm still getting stuck

Hi Daniel,

Can you confirm what the name of the partition is?

The kernel is currently expecting a partition called mmcblk0p1 (see the kernel logs above and the arguments supplied to the kernel for boot in the link below).

In such a case, you need to replace the expected rootfs partition name for mmcargs in u-boot:

https://github.com/analogdevicesinc/lnxdsp-adi-meta/wiki/Getting-Started-with-ADSP%E2%80%90SC598-(Linux-for-ADSP%E2%80%90SC5xx-Processors-3.1.2)#booting-linux-from-the-sd-card

Also, it looks like you are using gparted instead of the method mentioned. If not, could you share your logs from the terminal? I would like to confirm that everything being done is one to one. These pictures do not convey the exact steps taken.

Please note that for the first boot, things are configured in a very specific way and they should not be changed unless you have knowledge of what needs to be adjusted everywhere else to accommodate it.