EngineerZone Forum
Q&A from Analog Devices EngineerZone: SigmaDSP/SigmaStudio and DSP discussions (86 topics).
86 topics · 373 messages
Filtered by: #adau1451 ✕
-
Request for Review of ADAU1451 DSP Audio Architecture
Dear Analog Devices Support Team, I would like to ask for your support in reviewing the audio architecture of our system using the ADAU1451 DSP. System overview Host processor: Rockchip CM3588 DSP: AD
-
Indirect Parameter Access Table (IPAT) names in Sigma Studio +
I am working on converting an old sigma studio project to sigma studio + During that i found that is was lacking the option to chose a component to control via IPAT based on the name i have given the
-
difficulty writing to Indirect Parameters
Issue I am experiencing some difficulty when using the address in the IPAT table to try and change a variable. The code block I have attached is able to toggle an LED on and off by changing the value
-
Trouble connecting to module through sigma studio
Hello, We are attempting to use Sigma studio and ADUSB2EBZ USB adapter in order to debug our custom board but we are having a problem where we often get a "Compiled Comms Failed" issue when attempting
-
The difference between AVC and AGC
Hi, The block "AVC" is used. The curve of this AVC is as follows: it follows the input with a gain of -18dB and saturates at level of 0.538Vcc (crete-to-crete). The 0dBFS level is 1.1Vcc, so here 0.53
-
How to start simulation with SigmaDSP ? (for beginners)
Hi, I am a beginner with DSPs and I try to use an ADAU1452+DS42448 board. I have just bought the board and I try to use it, but it is another story !! Dave and Bob said that this DSP is the best one f
-
How do I modify this 2way project file to get the SPIDF output working on my HiFiBerry Beocreate 4ch amplifier?
I really need help on this or my boombox project is dead in the water! Here is a link to the 2-way project file I downloaded from HiFiBerry: https://www.hifiberry.com/wp-content/uploads/2017/10/2-way-
-
Can I use this circuit to use GPIO to control MUX ?
I want to use a GPIO to control a MUX in DSP. My GPIO connects to a hardware switch, when switch to SRC1 , it pulls high , when switch to SRC2, it pulls low. Then , I use this curcuit to control MUX i
-
(adau1451) How to make sure EEPROM settings are correct? if "Check last compilation throught DSP" always retrun fail.
Hi~ I am using adau 1451 design a car audio product. We had made PCBA, using adau1451 pin 28 (SCL ), pin 28 (SDA) to connect self boot EEPROM (AT24C256). pin 28, pin 29 using 2.2k resistor to pull up
-
SigmaStudio crashes when using TCP/IP communication
I have the exact same problem as detailed in this other post: SigmaStudio crashes on TCP communication with ADAU1451 - Discussions - SigmaDSP Processors & SigmaStudio Dev. Tool - EngineerZone (analog.
-
Project Stops Running after about 1 minute. 1452, Tone, Parametric EQ, Stimulus/Probe
I am running a simple project with a couple GPIO pins to illuminate the onboard LEDS (as a visual 'hearbeat' that the app is running), a couple 5 band parametric EQs and Level Controls. I also have tw
-
Parametric Equalizer reset to default
Hi ADI Tech Support, good day. we seek clarification on parametric equalizer. is there any commands or options that resets the parametric equalizer to default settings? for the use case, an external m
-
ADAU1451WBCPZ-RL - Recommendation details (Pull up / Pull down / Floating) for the pin (GPIO/I2S/I2C/SPI/SPDIF/THD)
Could you please share the Recommendation details (Pull up / Pull down / Floating) for the pin (GPIO/I2S/I2C/SPI/SPDIF/THD) pin also when it is not used. Audio Signal Processors adau1451 hardware sigm
-
I have ADAU1452 schematic that I need to run on an ADAU1451. Do i really need to redraw the whole schematic?
I developed a fairly large algorithm in SigmaStudio, which runs with about 90% instruction / cycles (just to give some indication of it's size). I've been testing / running the code on the EVAL-ADAU14
-
Interchangeability of ADAU1452/1451/1450 and ADAU1462/1466
Hello, As said in ADAU1462/1466 datasheet, it seems to be compatible pin to pin and in registers to the ADAU1452/1451/1450. I would like to know if this is really true and (with a reduced signal proce
-
ADAU1463/67 State of I2S Bus in RESET
Hey everyone, quick question about the ADAU1463/67 State of I2S-Bus-Pins in RESET Mode. I suspect the ADAU1463 is behaving similar to the ADAU1451 on the I2S-Pins, therefore the answer ( RE: DSP - ADA
-
SigmaStudio crashes on TCP communication with ADAU1451
I am running SigmaStudio 4.6 Build 0. Rev 1812 on Windows 10 Home 19043.1466 64-bit. Having just done a fresh install of SigmaStudio, I created a new project. I added my ADAU1451 and TCP communication
-
Register description for ADAU1451
I am working with the ADAU1451 on some DSP applications. Where can I find a document describing the full set of parameters that can be configured in the register, listed with parameter name, memory ad
-
DSP - ADAU1451 - State of pins during RESET
Hi, What is the state(Input or Output or High impedance) of the all the pins during RESET of DSP (ADAU1451). Audio Signal Processors adau1451 SigmaDSP Audio Processors
-
ADAU1451/2/equivalent: Ridiculous leadtimes, preventing adoption
We've been working on a new design that uses the ADAU1451. ADI is showing leadtimes to **2024** now on all of these and equivalents (1452, etc). That's absolutely absurd. Some of the distributors prom
-
Stereocoder 38Khz multiplex not working on adau1451
Hi, I build de stereocoder in adau1451 from the schema in adau1701. It works accept the 38Khz won't come out. Did try to change the clock settings and sample rate but solves nothing. Stereocoder-1701.
-
[ADAU1451] I2S microphone configuration with AEC algorithm
Hello all, I am not experienced in audio signal processing and I have never worked with SigamaStudio or any Analog Devices' DSP, therefore I am having some difficulties. I am using the HiFiBerry DAC+
-
ADAU1451 Multirate processing and clocks/start pulse/sampling rate settings problem
Hi, I’m having some troubles with multirate processing on the ADAU1451 (scheme below). I want to receive : 1) audio data at 48 kHz 2) have a first stage of processing at 48 kHz 3) then upsample the au
-
ADAU1452 code compatibility
Hello Everybody, I have a project in production using ADAU1451 where DSP code is loaded by an Application Processor trough I2C. Now we have some trouble to find the SIGMADSP part number and one of our
-
ADAU1451 ASRC_MUTE strange behaviour
Dear All, When ASRC do not have any valid input signal (no clock at input, ASRC unlocked) it should go to mute and output a data of 0 no ? Instead ASRC outputs a continuous data value. When ASRC is lo