EngineerZone Forum
Q&A from Analog Devices EngineerZone: SigmaDSP/SigmaStudio and DSP discussions (1149 topics).
1149 topics · 5595 messages
Filtered by: #45 ✕
-
External SPI RAM
Hi I am currently looking to build a 4 tap delay with up to 5 seconds of delay. Each tap will have individual filtering and different modulation options. I see that the ADAU1452 has an external RAM bl
-
ADAU1462 data memory size
Hello, According to the datasheet for the ADAU1462, the data memory size is 48kWords. However, according to the compiler output window in Sigma Studio 3.17: ADAU1452 - DM0: 20480, DM1:20480, PM: 8192
-
ad1938+adau1452 noise
Dear ADI staff: I designed a DSP board using AUAU1452 and AD1938, and controlled it using STM32F103RCT6 with a sampling frequency of 48K, using hardware mode, During testing, it was found that AD1938
-
AD1938+1ADU1452 NOISE
Dear ADI staff: I designed a DSP board using AUAU1452 and AD1938, and controlled it using STM32F103RCT6 with a sampling frequency of 48K, using hardware mode, During testing, it was found that AD1938
-
ADAU1452 + AD1938 Setting I/O problem
Hello, I bought a two-board set consisting of an ADAU1452 DSP and an AD1938 codec. I managed to get it up and running using a modified '192i2s.dspproj' test file. The sound quality is excellent. In my
-
[ADAU1452] Internal PU/PD States During and After Reset
Hi, We have a question regarding the status of the internal pull-up/pull-down (PU/PD) resistors during and after reset for the ADAU1452. Upon checking the ADAU1452 datasheet, we found a reference to i
-
Unconventional application of the ADAU1452 audio processor
I used an audio processor in a non-standard way for a metal detector. I want to be able to select a project (program) that will be loaded into the ADAU1452 from EEPROM by pressing buttons connected to
-
Request for Review of ADAU1451 DSP Audio Architecture
Dear Analog Devices Support Team, I would like to ask for your support in reviewing the audio architecture of our system using the ADAU1451 DSP. System overview Host processor: Rockchip CM3588 DSP: AD
-
Boot ADAU1452 from ESP32 without EEPROM (RAM loader via I2C)
Cześć, udostępnić rozwiązanie rozwiązania uruchamiania konfiguracji ADAU1452 SigmaDSP bezpośrednio z konfiguracji ESP32 za pośrednictwem interfejsu I²C bez użycia pamięci Selfboot EEPROM . W moim
-
write self-boot memory through DSP
Hello, I am working with a self made PCB with ADAU1452 and 25AA1024 SPI-EEPROM. The connection to the board works fine. I can get audio in and out of the DSP. But I am not able to write the last compi
-
View SECONDARY_I2C traffic in Capture Window?
In another thread, I saw a Capture Window log with IC 1.SECONDARY_I2C Block writes logged. I'm currently seeing I2C transactions on the secondary bus using a Beagle I2C analyzer, but I'm wondering how
-
Issues understanding the running average block
Hello thank you for taking your time to read my issue, I am attempting to design a logic flow to distinguish between two signals of the same amplitude (Value = 1.0): A sustained pulse with a duration
-
Odd problem with LRCLK
Hi, we have a product that used an ADAU1452 DSP processor and we are experiencing an odd problem with the LRCLK that we are sending into and using as a reference for, the SERIAL PORTS. Firstly, I see
-
Not seeing I2C traffic on SCL2_M,SDA2_M pins with ADAU1463
My circuit board has SCL2_M and SDA2_M connected to a DAC, ADC, and two AD2437 chips. This I2C bus has pull-ups on the PCB, immediately beside the ADAU1463 pins, and then the traces continue to the AD
-
Loading dsp data using esp32 holds i2c lines low
On ESP32 I program the ADAU1452 DSP over a shared I2C bus during startup (bulk writes of the DSP image). During this DSP load phase I have observed, on a logic analyzer that both I2C lines (SCL and SD
-
Understanding of gain stage, dsp headroom and serial port bit rates
Hello Ez, I am trying to properly understand the relation between gain stage, DSP headroom and serial port bit rates as the title says. The DSP is used as an active XO for stereo systems. It could be
-
Read/Write to EEPROM does not work anymore, but selfboot does
I've built a custom ADAU1452 board with a Winbond W25Q SPI flash. I have used this board with no issues for the last 6 months or so but I had to reconfigure it and for some reason I can't write to the
-
Programming ADAU1452 via I2C in SigmaStudio+
I have used SigmaStudio 4.7 for programming ADAU1452 via I2C, using a "custom" USBi. However, I can't seem to do that in the new SigmaStudio+. Using a custom platform block, there isn't a way to conne
-
DSP Readback is not working
I have a problem with the USBi 1.5, EVAL-ADAU1452REVBZ, and SigmaStudio 4.7 on Windows 10 Pro (22H2) where none of the DSP Readback blocks in my setup read anything but FFFFFFFF. Power (6V) is applied
-
ASRC Inter Sample Peaks - ASRC Input with gain
Hello EZ, I have successfully built my own 8 channel DSP based on the ADAU1466 and AK4493 DAC's. Now that the hardware works I am trying to get the hang of the more intricate parts of the DSP world. M
-
Aardvark does not turn green for EVAL-ADAU1452REVBZ
I have ordered the USBi interface, but I am trying to use the Total Phase Aarkvark with the EVAL-ADAU1452REVBZ in the mean time. For some reason, nothing I do seems to turn the Aardvark Communication
-
ADAU1452 doesn't start execution of program
Hi there, I've designed a custom PCB with an ADAU1452 DSP. There is also a Linux SOM, a Codec for ADC/DAC and two MAX98397 on the PCB. Right now I'm trying to get the DSP to work. I've programmed a ba
-
How to read the secondary path coefficients for MFxLMS?
hi: I followed the instructions on wiki.analog.com, but the secondary path coefficients I obtained were consistently 0. Audio Signal Processors adau1452 software filter SigmaDSP Audio Processors
-
Indirect Parameter Access Table (IPAT) names in Sigma Studio +
I am working on converting an old sigma studio project to sigma studio + During that i found that is was lacking the option to chose a component to control via IPAT based on the name i have given the
-
Export system Files .h SIGMA_WRITE_DELAY erroroneus call
I dont know if this is a bug Sigmastudio+ 3.3.0 wen i export system files , the .h generated, calls this function on SigmastudioFW.h, with four arguments SIGMA_WRITE_DELAY(DEVICE_ADDR_ADAU145XSCHEMATI