EngineerZone Forum
Q&A from Analog Devices EngineerZone: SigmaDSP/SigmaStudio and DSP discussions (942 topics).
942 topics · 4573 messages
Filtered by: #sigmastudio ✕
-
ADAU1701 self-boots and registers verify correctly, but Sdata_out0 (MP6) never outputs any data
Hi, i would need some help on my custom ESP32 + ADAU1701 schematic, i am stuck at an unusual issue and i cna't progress past it, please read below, will provide more info if needed, just say what that
-
Packing 8 16bit channels into one serial port
Hello! I'm designing V2 of my digital mixer, which uses an ADAU1466, ADCs, DACs, and an ESP32-S3 for the web interface. So far so good. V1 is working great, but for V2 I'd like to add multitrack recor
-
Current Maturity of Custom C/C++ Development on HiFi 3z Core?
Dear Team, We are evaluating the ADAU1797A for a hearable/audio application and need to implement a custom feature extraction algorithm (statistical/spectral analysis of the incoming audio stream) dir
-
Adding a sub out for a powered sub
New here. A couple years ago I made open baffles, with full range and woofers. I am currently using a car audio line level converter to the woofer wiring to feed my subwoofer. I want to use a PCM5102
-
TDM8 Connection on ADAU1467 Rev.B Evaluation Board (Brooklyn 3 + AK5578 Configuration)
I am currently evaluating an ADAU1467 Evaluation Board Rev.B and am having trouble getting the TDM connection to work correctly. If anyone has used a similar configuration or is aware of any important
-
SigmaStudio+ Indirect Parameter Accees Table
In old SigmaStudio you could add a parameter to the IPAT with a simple mouse right-click. Is there a similar feature in SigmaStudio+? I can only add it via the IPAT table but it gets annoying when the
-
left and right balance issues
Dear members, i want to know adau1401 how to created the left/right channel balance as pan function as below graphs, i tried below schematic, but no used, or we can use the volume table to find the lo
-
SigmaStudio+ Sample rate propagation
I found out that the T-Connector would not propagate sample rate downstream. Remove the T-Connector and connect straight to the next block and the block's sample rate follows upstream. Does anyone hav
-
Less Inst(cycles) in SS+ than in SS
My question is related to these two threads: - ez.analog.com/.../how-to-set-sample-rate-in-ss-like-done-in-4-7 - ez.analog.com/.../setting-sample-rate Preambule: I migrated a project from SSv4.7 to SS
-
Sigmastudio for Android devices
Hi, I apologize for asking this question here. I just don't know where to look. Is there a programming environment similar to SigmaStudio where you can build an audio processing block and then run it
-
SPDIF TX configuration and timing problems between chained devices
Hi Team, I have a custom made DSP board for a loudspeaker based on the ADAU1466 and currently having a problem with my S/PDIF signal chain. I run an ADC (@96khz) on SIDN1 through a ASRC2 into the DSP
-
Where is dither?
The Data Sheet section on Hardware Accelerators says "The core includes accelerators like division, square root, barrel shifters, Base 2 logarithm, Base 2 exponential, slew, and a pseudorandom number
-
Boot ADAU1452 from ESP32 without EEPROM (RAM loader via I2C)
Cześć, udostępnić rozwiązanie rozwiązania uruchamiania konfiguracji ADAU1452 SigmaDSP bezpośrednio z konfiguracji ESP32 za pośrednictwem interfejsu I²C bez użycia pamięci Selfboot EEPROM . W moim
-
Issues understanding the running average block
Hello thank you for taking your time to read my issue, I am attempting to design a logic flow to distinguish between two signals of the same amplitude (Value = 1.0): A sustained pulse with a duration
-
Not seeing I2C traffic on SCL2_M,SDA2_M pins with ADAU1463
My circuit board has SCL2_M and SDA2_M connected to a DAC, ADC, and two AD2437 chips. This I2C bus has pull-ups on the PCB, immediately beside the ADAU1463 pins, and then the traces continue to the AD
-
Use of Custom dll blocks from older versions of SigmaStudio
I have a number of custom blocks, dll's that have been in use for many years running of SHARC as well as ADI platforms in regular Sigma Studio. We have customers looking to use some of the newer platf
-
TDM2 oder 8 channels
Hey together, one question. We know that it is possible to send 16 channels of audio via serial port 0/1 via a single SDATA pin (16 channels), via 2 SDATA pins (2x8channels) and 4 SDATA pins (4x4chann
-
How to make a 10 band audio equalizer controlled by 10 analog pot, using an adau1701 and two CD4051
Hi, I want to create a 10-band audio equalizer (31Hz-16kHz) using the ADAU1701 and controlling it with 10 slide potentiometers. I want to read the potentiometer readings using the same DSP without an
-
Understanding of gain stage, dsp headroom and serial port bit rates
Hello Ez, I am trying to properly understand the relation between gain stage, DSP headroom and serial port bit rates as the title says. The DSP is used as an active XO for stereo systems. It could be
-
Enable second I2C port on ADAU146x chips?
What are all of the settings necessary to enable the second I2C port on the ADAU146x series of SigmaDSP chips? I have designed and fabricated a board based on the ADAU1463. The only device on the SPI_
-
How to view I2C Read data
I am hoping to use SigmaStudio+ to debug the I2C link between an ADAU1463 and DAC chip. I added the I2C Read External Trigger, connected an On/Off button to the trigger input, and connected the output
-
How to set Sequence File for Control Port IO?
I have a Custom Platform (for ADAU1463) with multiple Control Port IO modules (for A2B chips, ADC and DAC), but I cannot find out how to specify the Sequence File in the Settings. I can click on Setti
-
Readback Block
I'm trying to read data from my readback blocks in an Arduino/platform IO project. The readbacks are layed out as follows in my .dspproj In my code, I'm attempting to read the register values using th
-
Programming ADAU1452 via I2C in SigmaStudio+
I have used SigmaStudio 4.7 for programming ADAU1452 via I2C, using a "custom" USBi. However, I can't seem to do that in the new SigmaStudio+. Using a custom platform block, there isn't a way to conne
-
[Bug Report] Sigmastudio+ 3.3 Full screen mode incorrect in some displays.
Currently I use the display of my laptop, plus an external 4K display. When setting Sigma+ in full screen in the 4K display, the right side of the window is cropped (like it was outside the display).