EngineerZone Forum
Q&A from Analog Devices EngineerZone: SigmaDSP/SigmaStudio and DSP discussions (431 topics).
431 topics · 2071 messages
Filtered by: #adau1761 ✕
-
Generate a single pulse with ADAU1761 and Sigma Studio
As I'm a new user, Hi Everyone! I hope you can help me with my problem. I have the EVAL-ADAU1761Z board and I need to generate a single square pulse and send it to HP Out. The pulse has to be 100µs an
-
Schematic review request for the ADAU1761.
Hi David, As I have posted in the wrong space (Precision Microcontrollers), Now I am posting in the sigma DSP section. Now I am replying to the answer mentioned in the Precision Microcontroller sectio
-
Query about PLL Lock in ADAU1761
Hello, we do use ADAU1761 in our module. The masterclock ADAU1761 MCLK is provided by a MPU , MCLK frequency is 26MHz. There are 2 power modes of the MPU (RUN and Low Power). The MCLK signal from MPU
-
Shift incoming I2S data left 7 bits
For reasons that are too long to explain here, the I2S data is arriving (logically) shifted right 7 bits. This is fine because it's really just 16 bits of valid data. Before I can use the data I need
-
Inquiry on ADAU1761 extern MCLK Clock Synchronization and CRC Verification Method
Hello Teams, In a custom project, the MCLK for the ADAU1761 is sourced from an external chip (referred to as Chip B). Since the main control chip (MCU) cannot determine the exact time when Chip B outp
-
ADAU1761 PLL issues with MCLK 24.576mhz
Hi If I set the PLL to Integer mode Input DIV =1 PLL Integer =2 R2 PLLCRL = 0xXXXX XXXX 1001; Thus MCLK 24.576 = Core Clock 49.152 The PLL will not lock If I set the PLL to Integer mode Input DIV =2 P
-
Parametre generator for ADAU1761 Peaking filter
Hello EZ - i am currently writing a C driver for several future products and i have reached a challenge i need help with: Assignment: The hardware guys have made an implementation that uses these filt
-
any way to generate harmonic from basic frequency?
Hello The previous analog design uses a JFET input, while the new design uses an OPAMP + DSP(ADC/DAC) to do signal processing. need to know how to generate harmonic from to Best regards Power Pan Audi
-
Thermal Parameters for the thermal analysis
Hi team, In our development project, we are using following ICs and we need to do the thermal analysis for the PCB. For the analysis, we require the θJA (°C/W), θJC (°C/W), θ
-
Trying to output sound on headphones from I2S signal
Hello, I send an I2S signal to the DAC input of the ADAU1761 (through J6 connector on the ADAUX61EBZ board). I checked it with a logic analyzer and I can see it correctly. I'm using the onboard oscill
-
MCLK issue and replicable Adau chip
Hello every , and Hello DAVE, I look into this ADIEngineerZone for long time, but this is my first time post here. I have a Bluetooth project using Adau1761, the Bluetooth chip cannot generate MCLK to
-
Programming ADAU1761 using Sigma Studio Capture Window Address + Data sent from microprocessor Circuitpython via I2C
I am (usualkly) successfully able to use address and data copied from the capture window of Sigma Studio to program an ADAU1761 via I2C. I use CircuitPython running on an nRF52840-based microprocessor
-
ADAU1761 not working on the ADAA24XX-EV-B2BX Eval Board
Hi I am using the ADAA24XX-EV-B2BX board which contains a ADAU1761. I want to implement a basic audio input output with an audio jack connected to P8. Implementing the system below in Sigma Studio the
-
Frequency limitation
The manual for the ADAU1761 states that the maximum sampling rate is 96 kHz. We use SigmaStudio for signal processing. Even if we only have input and output, we cannot pass through a wave with higher
-
Read from ADAU1761 over SPI
Hello EZ Community, I am trying to setup the ADAU1761 using SPI on our prototype board. So far I’ve had no success setting it up or reading from it. Initially i tried reaching out to technical support
-
Getting started with sigma studio
I need to make basic program in sigma studio for codec adau1761 custom board, export it as c program. Pls suggest how to get started? Thanks. Audio Signal Processors software SigmaDSP Audio Processors
-
adau1761 NLMS/adaptive filter question
Hello first time using NLMS, need some help on this project. goal: while ARM is playing music the MIC should remove the music signal from its own speaker. attached is the schematic and the project fil
-
SigmaStudio+ user interface
Hi, SigmaStudio+ has an ancient user interface. Please develop a new useful and flexible user interface. If possible, the VSCode interface is better and more modern for all users. Best Regards, Audio
-
ADAU1761 PEQ biquad filter question
Hello, ADAU1761.dspproj biquad question again. When we tested the output waveform, we found that the simulation differed from the PEQ window. so which result could we trust? this result is what we exp
-
How to make the digital Mic ICS-43434 with ADAU1761 work well?
I ever use the analog Mic to work with ADAU1761, and it works well. Now I would use one digital Mic ICS-43434(made by TDK InvenSense,alike INMP441,), but it doesn't work. The Hardware conection as bel
-
Fading clicks (similar to echo in a cave) ADAU1761 HP out
Hello! I encountered strange artifacts at the output of the ADAU1761 headphones. System: some USB-I2S transport + ADAU1452 + AD1938 + ADAU1761. The sound is normal on the analog outputs of the AD1938.
-
Software differential signal generator (or MP3 player for that matter)
I chose ADAU1761, but the topic is not only related to ADAU1761. I would be grateful if the administration moves the topic to a right place. Colleagues, I have an idea to have a pocket differential si
-
ADAU1761 audio codec on zedboard
I have written HDL code to program zedboard and able to listen loopack audio from HPH out and giving audio in from line in Jack. I don't want to play loopback audio, I want to play the audio which is
-
adau1761
Hi, I need a guide for the coefficient calculation for IIR filters. attached is a straightforward project but I have a calculation problem. 7318.Design 1.dspproj the project needs to set many IIR filt
-
ADC capture > RPi > DAC output - is this possible?
All I want to do is use the ADAU1761's ADC and DAC separately to capture and play back audio. ADC to Raspberry Pi for processing, then the Raspberry Pi to the DAC for playback. Is this possible? Sigma